Validation of a CFD model by using 3D sonic anemometers to analyse the air velocity generated by an air-assisted sprayer equipped with two axial fans
García Ramos, Francisco Javier (Universidad de Zaragoza) ; Malón Litago, Hugo (Universidad de Zaragoza) ; Aguirre,A. J. ; Boné Garasa, Antonio (Universidad de Zaragoza) ; Puyuelo,J. ; Vidal Cortés, Mariano (Universidad de Zaragoza)
Resumen: A computational fluid dynamics (CFD) model of the air flow generated by an air-assisted sprayer equipped with two axial fans was developed and validated by practical experiments in the laboratory. The CFD model was developed by considering the total air flow supplied by the sprayer fan to be the main parameter, rather than the outlet air velocity. The model was developed for three air flows corresponding to three fan blade settings and assuming that the sprayer is stationary. Actual measurements of the air velocity near the sprayer were taken using 3D sonic anemometers. The workspace sprayer was divided into three sections, and the air velocity was measured in each section on both sides of the machine at a horizontal distance of 1.5, 2.5, and 3.5 m from the machine, and at heights of 1, 2, 3, and 4 m above the ground The coefficient of determination (R2) between the simulated and measured values was 0.859, which demonstrates a good correlation between the simulated and measured data. Considering the overall data, the air velocity values produced by the CFD model were not significantly different from the measured values.
Idioma: Inglés
DOI: 10.3390/s150202399
Año: 2015
Publicado en: SENSORS 15, 2 (2015), 2399-2418
ISSN: 1424-8220
Factor impacto JCR: 2.033 (2015)
Categ. JCR: INSTRUMENTS & INSTRUMENTATION rank: 12 / 56 = 0.214 (2015) - Q1 - T1
Categ. JCR: CHEMISTRY, ANALYTICAL rank: 36 / 75 = 0.48 (2015) - Q2 - T2
Categ. JCR: ELECTROCHEMISTRY rank: 16 / 27 = 0.593 (2015) - Q3 - T2
Tipo y forma: Article (Published version)
Área (Departamento): Ingeniería Mecánica (Departamento de Ingeniería Mecánica)
Área (Departamento): Expresión Gráfica de la Ingeniería (Departamento de Ingeniería de Diseño y Fabricación)
Área (Departamento): Ingeniería Agroforestal (Departamento de Ciencias Agrarias y del Medio Natural)
0
Exportado de SIDERAL (2016-06-27-10:30:22)
Idioma: Inglés
DOI: 10.3390/s150202399
Año: 2015
Publicado en: SENSORS 15, 2 (2015), 2399-2418
ISSN: 1424-8220
Factor impacto JCR: 2.033 (2015)
Categ. JCR: INSTRUMENTS & INSTRUMENTATION rank: 12 / 56 = 0.214 (2015) - Q1 - T1
Categ. JCR: CHEMISTRY, ANALYTICAL rank: 36 / 75 = 0.48 (2015) - Q2 - T2
Categ. JCR: ELECTROCHEMISTRY rank: 16 / 27 = 0.593 (2015) - Q3 - T2
Tipo y forma: Article (Published version)
Área (Departamento): Ingeniería Mecánica (Departamento de Ingeniería Mecánica)
Área (Departamento): Expresión Gráfica de la Ingeniería (Departamento de Ingeniería de Diseño y Fabricación)
Área (Departamento): Ingeniería Agroforestal (Departamento de Ciencias Agrarias y del Medio Natural)
0
Exportado de SIDERAL (2016-06-27-10:30:22)
Este artículo se encuentra en las siguientes colecciones:
articulos > articulos-por-area > expresion_grafica_de_la_ingenieria
articulos > articulos-por-area > ingenieria_agroforestal
articulos > articulos-por-area > ingenieria_mecanica
Notice créée le 2016-03-16, modifiée le 2016-10-06
Liens externes:
Versión publicada
Versión publicada
Versión publicada
Versión publicada